Experimental investigation of effect of tool path strategies and cutting parameters using acoustic signal in complex surface machining

High productive milling of complex sculptured surfaces is extremely important in many different industries. Determination of the appropriate tool path styles and milling parameters is crucial in ensuring precise surface machining, meeting the better surface integrities and lower tool deflection and forces using process monitoring methods. In this study, sound pressure as a monitoring method is presented for analyzing different tool path strategies and cutting parameters to assess their influence on surface errors, tool deflection, cutting forces, sound pressure level and instantaneous material removal rate on rough machining of complex surfaces with ball end mill. Design and analysis of experiments are performed using factorial design technique and variance analysis. Additionally, the significant parameters affecting the experimental results are introduced. B-rep based method with integrated CAM software is developed to calculate the cutter/workpiece engagement, effective cutting diameter and instantaneous material removal rate. Milling strategies employed include contour parallel, zigzag with two cut angle, and spiral. The milling conditions were feed rate and radial depth of cut. The conclusion is that 0° zigzag strategy provokes the lowest cutting forces, tool deflection, surface errors and sound pressure and spiral strategy signifies the worst surface errors and the highest cutting forces. With the increase of feed rate, instantaneous material removal rate increases parallel to rising of machining sound signal, milling forces, tool deflection and machining errors. It is observed that the step over value has less influence on the results. The sound pressure level which has a drastic reference to the material removal rate and removed volume values are detected and experimental results could be figured out with sound pressure.


Introduction
Complex surfaces are widely used in the die/mold, aeronautics, shipbuilding, precision manufacturing, bio-medical and other sectors.The machining of free-form surfaces is a process that is both time-consuming and costly.There are more than 10,000 tool movements observed in a typical example of free-form surface machining as shown in Fig. 1.Tool-path characteristics are key parameters that determine not only the efficiency of the cutting processes but also the surface quality of finished parts.An optimal path generation method should be robust, accurate, precise and efficient.Kurt and Bagci [1] and Lasemi et al. [2] reviewed the recent research literature on milling of complex-curved surfaces and feed-rate optimization approaches.Chen et al. proposed a real-time monitoring system with error compensation in order to enhance dimensional accuracy in the production of complex components [3].Habibi et al. modeled machining process for force/deflection calculations in a 3D simulation environment [4].Desai et al. determined the effect of different curvature geometries by milling from two parametric directions and using cutting tool of various diameters [5].Alberti et al. [ 6] compared the part errors with cutting time in machining of Al material.Erdim et al. published a method to adjust feed-rate according to milling force in order to reduce machining time [7].Kaymakci and Lazoglu [8] suggested a new model to predict 3D surface topographies with integrated milling software.Gok et al. focused on investigating of effects of milling strategies on surface roughness for inclined surfaces using different coated cutter [9].Shajari et al. investigated various tool paths in 3-axis machining of a curved geometry part and also developed an approach for mathematical model to measure scallop height size and distribution [10].Izol et al. studied comparison and evaluation of the milling strategies to produce components with freeform surfaces [11].Matras et al. presented the analysis results of dimensional accuracy after the sculptured surface cutting simulations for different milling strategies [12].Schützer et al. developed an approach to use complex features to enhance the automatic creation of milling data.Their approach reduces the programming time significantly to produce HSC appropriate tool paths for same quality [13].The objective of the observation of cutting processes are related to the productivity of the milling center, cutter life, surface tolerances/texture properties, cutter flexibility/deflection, and other parameters of the part as well as the chip geometry, generation and classification.TCMSs have been obtaining significancy in sector and scientific works for approximately three decades.For this motivation, scholars have dedicated to development of TCMSs [14,15].Over the last three decades, different sensing elements such as milling force, spindle and cutting power, noise/sound measurement sensors have been commonly used to determine cutter life, wear, deflection and chatter etc. [16][17][18][19][20]. Acoustic emission [21], cutting force [22], power consumption [23] and cutting sound [24] that are created during milling have been worked to observe and optimize the cutting process automatically.Microphones are inexpensive and non-contact sensor, flexible to set-up in the NC machine and are used commonly for vibration and chatter detection and monitoring of tool life and wear in turning processes [25][26][27].The main serious issue relevant to the practice of sound signal in machining sector is the ability to insulate the sensing element from the dangerous machining environment [28][29][30].Machining oils or removed material can damage the acoustic sensing element.Vibration/noise signal from other machines, mechanical units, drivers, etc. or other factors can affect the sound signals.This noise can be filtered by using signal processing algorithm.Some researcher has used machining acoustic measurement approaches to observe cutting parameters [31] or cutting tool wear [24].Trabelsi et al. researched acoustic radiation from a microphone for cutter failure and wear evaluation in lathe machine using pattern-recognition methods [32].Teti et al. [33] summarized acoustic measurement approaches used to observe tool wear in turning process.Sound signal was examined in order to detect the relationship between acoustic signal and cutting parameters.Acoustic signal in representing time was employed using various works to monitor the variate in amplitude in accordance with cutter wear [25,26,34,35].
Tekiner used sound signals in order to find the optimum turning conditions [34].Raja concluded that with the change of machining conditions, acoustic pressure also changes and an increase in cutter wear results in an increase of cutting sound signal amplitude [25].Quintana used acoustic methods to detect the stability lobe in a machining process using sound mapping techniques.Downey used acoustic signals and compared the cumulative sound spectrum and roughness for the tool life [36].Delio et al. [37] presented that acoustic method is a proper approach for finding cutting vibrations during the milling.The acoustic signal from the chatter generated in the tool/workpiece engagement area was used to monitor toolvibrations [37][38][39][40][41]. Schmitz et al. [38][39] and Schmitz [40] examined a new method for milling vibration determination and recognition using statistical considerations.Weingaertner et al. [41] evaluated milling stability using audio signal measurements.Bagci [42] used sound pressure level in order to analyze the effect of MRR-based feed rate optimization approach on ball end milling process.In previous works, sound values were applied to observing of the different machining processes such as laser cutting, turning and hole making.Most of the previous works focused on comparing cutter deflection, cutting forces and surface errors with respect to cutter path orientations, but none of them examine cutter deflection, cutting forces, sound pressure, IMRR and surface errors regarding tool path strategies specially when rough milling of complex surfaces.In this work, we focus on machining of complex surfaces.When a ball end mill moves into different regions of complex surface which is included complex curved geometries, variations its machining direction, tool/workpiece engagement zone, swept volume, IMRR values, cutting depth are typically varied.
Because of these reasons, determination of cutting parameters is a high critical step so as to prevent unwanted outcomes, for example, cutter failure, or excessive material removal rate due to cutter deflection, dimensional errors.This work investigates the possibility of using acoustic signal to observe the complex surface machining and to evaluate effect of cutting parameters and tool path strategies.Firstly, the aim of this article is to examine various tool path strategies including contour parallel, spiral, and zigzag tool paths with different cut angle in 3-axis rough machining of complex surfaces.Secondly, the effect of cutting conditions on cutter deflection, cutting forces, sound pressure and surface errors based on the tool path strategy employed is investigated and the most significant parameter affecting experimental results is identified by means of analysis of variance.The machining parameters used in this study are feed rate, and radial depth of cut.Machining forces, tool deflection, sound pressure levels, surface errors were measured and IMRR values are analyzed.This work focuses on the potentiality of using sound signal to observe the complex surface machining at various process parameters.

Cutting tools and workpiece materials
Two fluted-carbide ball end mill cutter (12 mm diameter/nominal helix angle of 30°) was used.The chemical elements and structural specifications of the Al 7075-T651 were taken in Table 1.The cutters were held in a BT-40 taper tool holder.The experiments were conducted using a 3-axes CNC machining center which has a maximum spindle speed 12000 rpm and drive power 10 KW as seen in Fig. 2.This machine was designed to make 3-axis linear and circular interpolations via ISO format programs in metric and imperial units.Its control unit was a FANUC series O-M.
The rectangular samples (100×53×30 mm) of Al 7075-T651 aerospace alloy were used for the experiments.Several program packages were used in the evaluation of the data and in the experimental design of the study.The specimen was designed in CATIA V5 R17.

Milling conditions
Determination of the appropriate tool path styles and milling parameters is crucial in ensuring precise surface machining.For examining the influence of side step and feed rate value and tool path strategies in milling of free-form surfaces, the ten experiments were run at various conditions as seen in Table 2. Various machining strategies can be used for the same shape.Three tool path patterns were applied to the free-form surface in Fig. 3.Besides these three alternatives, the zig-zag type was used together with two different cut angles (0° and 45°).Tool-path strategies were compared in terms of cutting force, deflection, IMRR, dimensional error values and sound pressure values.Constant pick feed of 3 mm was used for all cases.In cutting tests, spindle speed was 600 rpm.The cutter is parallel to axis, and the maximum and minimum depths are 5.5 mm and 1.5 mm respectively for this part.

Cutting forces and tool deflection measurements
Cutting force measurements ( , , and ) were made using a Kistler 3-component piezoelectric type 9257 A dynamometer.The cutting force values were downloaded from the electronic unit reserved onto a notebook and after processing of the measured signal analysis is executed using Kistler software.The machined surface, CAM simulation and cutting forces were shown in Fig. 4. Machining forces are the principal factors managing cutting precision, surface properties, chatter, energy demands, and cutter wear.Cutting forces and tool deflection values were measured for various tool path patterns as shown in Fig. 5. Cutter deflection measurement has been performed using two accurate LVDT sensors installed at 90° and from another sensor and an aluminum ring was fixed to the flute of the cutting tool as seen in Fig. 6.

Measurement of machining errors
A 3D optical measuring system based on fringe projection was used to determine the machining errors in the workpieces by analyzing the different textural properties to the body.The 3-D optical scanning provided point cloud, curves and meshed data.The obtained data were indexed into the CAD software, which computed and displayed the deviations between the two data sets, as shown in Fig. 7.

Accurate calculation of instantaneous MRR and removed volume
The in-house API simulation software based on B-rep was used for calculation of instantaneous MRR and removed volume values.The IMRR value can be obtained by calculating the tool/machine part engagement geometry through the teeth transition duration ( ) and the volume is divided by to compute the average MRR.The chip thickness at any position on the cutting tool is determined by dividing the scalar product of the feed rate ( ) with the normal vector ( ) by the number of cutter tooth ( ), multiplied by the tool rotation values ( -rpm) [1].The material removal rate is the ratio which each cutting tool teeth removes material.The IMRR value is calculated via integrating the chip thickness along cutter flute that is actually engaged in the tool/workpiece contact zone as seen in Eq. ( 1) and Fig. 8 [1]: IMRR values were obtained for the different cutting strategies as shown in the Fig. 9.It is obvious that SPL value, cutting forces and tool deflection profiles and frequency values raise as the IMRR value raises.IMRR values were presented for three tool path patterns as shown in Fig. 9.

Measurements of sound pressure level
In this paper, the sound collected from experiments were analyzed in the time and frequency domain so as to identify the frequency scope in the acoustic signal that could then be used for process observing.The microphone was fixed at a length of nearly 30 mm from the cutter and acoustic signals are measured, recorded and analyzed on a software as shown in Fig. 2. In order to verify the repeatability of the experiments, the sound signal should be collected for each experiment and several times.The periodic impacts of the cutter with the machined part and the resulting tool deflection and chatter that arises hence creates a sound signal.This signal is a transmission of impact energy that propagates through the air and contains information about the process.Sound pressure is a logarithmic measure of the effective sound pressure of a sound relative to a reference value.It is measured in decibels (dB) above a standard reference level [42]: where is the reference sound pressure and is the rms sound pressure being measured.The sound signal was obtained by a microphone, and amplified using the DAQ module.Sound pressure values were presented as shown in Fig. 10 13(b) is analyzed, it becomes clear that cutting process occurs in 8 steps.SPL values of each cutting step, entry and exit points of the cutter onto workpiece, and the corresponding frequency values are clearly seen.A higher milling forces and tool deflection mean the trend to machining sound is bigger.The magnitudes of the fundamental acoustic signal frequencies when performing feed rate of 144 mm/min were monitored to be larger than that of feed rate of 48 mm/min as seen in Figs. 13 and 16.More considerably for feed rate of 144 mm/min, the harmonics between 2600 and 3000 Hz were denotive that tool deflections probably due to ball end mill run-out appeared with high magnitudes.It can be understood that peak frequency values range between 2600-3000 Hz and that they raise since more removed materials are made distant in 8th cutting step.
where, -feed rate in mm/min, -side step value in mm, -cutting force in , -tool deflection in mm, -Machining Error (mm) and -sound pressure level in dB.The models obtained are as follows.In regression analysis, is the regression coefficients ( 0.80) for the models denote that the fit of the measurement result is adequate.

Analysis of variance (Anova) of results
Analysis of Variance is an approach most commonly used for calculating significant parameters on experimental results and predicting their effects.The percentage contribution can be computed using Eq. ( 7): where is the sum of squared deviations.Analysis of variance results are given in Table 3. Percent (% ) is defined as the significance rate of the control parameters on the results.In the analysis the -ratio is a ratio of the mean square error to the residual error and is traditionally used to determine the significance of a factor.It can be seen from Table 3 that side step and feed rate, influence cutting forces by 1.17 %, 98.48 % in the milling of free-form surfaces, consecutively.The main effect plot for cutting forces are depicted in Fig. 16.It is shown that the milling forces increase with rise in the feed value.It is observed from main effects plots that, as feed rate increases from 48 to 144 mm/min, cutting forces increases from about 345 N to 740 N for side step 3 mm.It is observed that cutting force increases from 370 to 760 N when the feed rate value for side step 5 mm is raised from 48 to 144 mm/min.Side step' effect on cutting forces hasn't been observed.
It can be observed from Table 3 that the feed rate was found to be the only significant factor on the tool deflection with percent contribution of 94.59 %, followed by step over which contributed 3.40 % in the milling of free-form surfaces.In Fig. 17, the main effect plots for cutter deflection are plotted.Increasing of feed rate leads to increase tool deflection.It is observed from main effects plots (Fig. 17) that, as feed rate increases from 48 to 144 mm/min, tool deflection increases from about 0,7 to 1,25 V for side step 3 mm.It is observed that tool deflection value increases from 0.73 to 1.3 V when the feed rate value for side step 5 mm is raised from 48 to 144 mm/min.It was observed that the step over value has less influence on the magnitude of tool deflection.In Fig. 18, machining sound signals in various feed rate and step over values are given and compared.The signal values increased with the rise of feed rate values.It can be viewed from Table 4 that step over and feed speed influence sound pressure level by 0.048 %, 92.09 % in the milling of free-form surfaces, consecutively.The main effects plot indicates that sound pressure value is significantly influenced by feed rate as shown in Fig. 19.It is clearly seen from the graphs that sound pressure level increases as feed rate increases, this may be due to the fact that when feed rate increases the amount of material coming into contacts with cutting tool increases, therefore the load on the cutter also increases.The variation in step over has no effects on the sound signal.In Fig. 20, the main effect plots for machining errors are plotted.Increasing of feed rate and step over lead to increase machining errors as shown in Fig. 19.It can presented from Table 4 that cutting conditions were found to be significant factors on the milling error with percent contribution of 39.38 % and 48.59 %, respectively.

Discussion of experimental results
One of the main sources of unwanted dimensional error in rough machining process is the cutter deflection resulting from the periodic milling forces.In Fig. 21  cutter deflection and forces also increased parallel to the rise of acoustic signal values as shown in Fig. 19.It is observed from Fig. 19 that, as feed rate increases from 48 to 144 mm/min, sound pressure increases from about 52 to 61 dB for side step 3 mm.It is observed that sound pressure level increases from 53 to 63 dB when the feed rate value raises from 48 to 144 mm/min for side step 5 mm is.By lowering the feed value as 48 mm/min, the minimum sound signal levels and cutter deflection were acquired.It can be probable to express the relationship between cutter deflection and acoustic signal values.
When the acquired SPL and error graphics for different step over values were examined, it was observed that machining errors values increase with the rising of sound signal values.Besides, machining errors decrease with the decreasing of sound signal values.In accordance with Fig. 21, for the different step over values, the largest SPL of 63 dB results in the highest machining errors value of 0,47 mm at the test 10.Besides, the minimum SPL of 52 dB is obtained at the error value of 0,13 mm at the test 5.
Step over value has no significant effect on the machining surface errors.It was observed that the step over value has less influence on the magnitude of tool deflection, cutting forces and sound pressure level.It can be observed from experimental results that feed rate and step over affect sound pressure level by 92.09 %, 0.048 %, tool deflection by 94.59 %, 3.40 %, cutting forces by 98,48 %, 1,17 % and machining errors by 39.38 % and 48.59 %, in the milling of free-form surfaces, consecutively.The relationship between cutter deflection and cutting forces/cutter deflection and sound signal value/ cutting forces and sound signal value/ machining error and sound signal value during milling at all feed rates is strong, positive, and actuarially significant.Correlation coefficients between sound pressure level and other results (forces, deflection and machining errors) at feed rate values were better than = 0.7.This result is supported by the works of Jaromír [43] and Bagci [42], they observed that sound signal values increased with the milling forces due to rising of the feed rates.When the feed rate value was rised from 48 to 144 mm/min, the magnitudes of the frequency elements increased.
It is observed from Fig. 22 that when milling with spiral strategy, the highest cutting force, tool deflection and sound pressure values were observed followed by 45° zigzag, 0° zigzag and contour parallel strategies, respectively.It results from the interrupted cutting which occurs at the tool entry and exit positions at the machined part.The high impact forces are created when cutter steps into the part.Because of a sudden increase in removed volume as shown in Fig. 9, the in feed executed inside the machine part results in excessive vibrations due to increased cutting forces and tool deflections.Employing contour parallel strategy achieves the lowest cutting force magnitude.In complex surface machining, cutting depth and IMRR values are invariably fluctuating at each cutter location point, for this reason different levels of surface-errors are left on free form surface. Since the comparison between strategies takes place in similar machining conditions, tool-chip contact area and IMRR values are main reasons for sound pressure differences between various strategies as shown in Fig. 23.

Conclusions
The effect of various tool path strategies on cutter deflection, cutting force, surface error, IMRR and acoustic signal values when rough machining of complex surface of Al 7075-T651 was investigated.Additionally, the influence of radial depth of cut and feed rate on output characteristics was evaluated in accordance with ANOVA and regression analyses.This work focuses on the potentiality of using sound signal to observe the complex surface machining at various process parameters.The conclusions obtained from the present study are as follows: 1) The main result of this paper is that the acoustic signal collected during the machining of free form was well correlated through the ball end milling with the cutting forces, IMRR, tool deflection and surface error values where the variations in feed rate are explicitly observed.With the increase of feed rate, instantaneous material removal rate increased parallel to rising of machining sound signal, milling forces, tool deflection and machining errors.It was observed that the step over value has less influence on the magnitude of tool deflection, cutting forces, machining error and sound pressure level.
2) For the different step over values, the higher SPL value (63 dB) lead to the higher machining errors value of 0,47 mm at the test 10.On the other hand, the minimum SPL value (52 dB) is recognized at the error value of 0,13 mm at the test 5.
3) As the data presented in this paper have shown that the use of various tool path styles when rough milling of free form surfaces has significant effects on the tool deflection, cutting forces, surface error, and sound pressure.In general, contour parallel tool path appears to provide preferred results in terms of lower IMRR values, cutting forces, deflections, sound pressure and machining errors values.It is observed that when milling with spiral strategy, the highest cutting force is observed as a consequence of tool-chip contact area followed by 45° zigzag, 0° zigzag and contour parallel strategies, respectively.Because of an abrupt increment in removed volume, the in feed executed inside the machine part results in excessive vibrations due to increased cutting forces and tool deflections.
4) The acoustic signal which has a reliable relation to the IMRR and removed volume values were detected and experimental results could be figured out with sound pressure.It is concluded that sound pressure and frequency values raise as the tool/workpiece engagement area and removed volume values increases.

Fig. 1 .
Sculptured surface definition and examples

Fig. 4 .
a) CAM simulation, b) machined part, c) force values for experiment 10

Fig. 5 .
Cutting forces and tool deflection values for three tool path patterns a) b) Fig. 6. a) Deflection measurement set-up, b) deflection profile for experiment 10 a) b) c) d) Fig. 7. a), b), c) Obtaining of CAD model and error values, d) of surfaces using fringe projection

Fig. 9 .Fig. 10 . 10 Fig. 11 .
Fig. 11.Variation of SPL values for various tool path strategies Fig. 13 reveals the comparison of the frequency spectrums of the acoustic signal for 48 and 144 mm/rev feed values.When the Fig. 13(b) is analyzed, it becomes clear that cutting process occurs in 8 steps.SPL values of each cutting step, entry and exit points of the cutter onto workpiece, and the corresponding frequency values are clearly seen.A higher milling forces and tool deflection mean the trend to machining sound is bigger.The magnitudes of the fundamental

Fig. 14 Fig. 12 .Fig. 13 .Fig. 14 .
Fig. 15 shows spectrogram of the time tracking of the magnitude of acoustic signal at the frequencies of the processing measured signal for various tool path trajectories.The sound was

Fig. 15 .
Spectrograms for: a) 0°zigzag, b) 45° zigzag, c) contour parallel, d) spiral tool paths INVESTIGATION OF EFFECT OF TOOL PATH STRATEGIES AND CUTTING PARAMETERS USING ACOUSTIC SIGNAL IN COMPLEX SURFACE MACHINING.EYUP BAĞCI

Fig. 18 .Fig. 19 .Fig. 20 .
Fig. 18.SPL results for different milling conditions are shown the variations observed in cutting forces, cutting tool deflection, sound pressure level and machining errors as a function of the feed rate values for different step over values.With the increment of feed rate,

Fig. 23 .
Fig. 23.Relationship between Max.IMRR and sound pressure values for different strategies 2693.EXPERIMENTAL INVESTIGATION OF EFFECT OF TOOL PATH STRATEGIES AND CUTTING PARAMETERS USING ACOUSTIC SIGNAL IN COMPLEX SURFACE MACHINING.EYUP BAĞCI

Table 1 .
Chemical composition and mechanical properties of Al 7075-T651
No Tool path strategiesFeed rate (mm/rev) Step over (mm)

Table 3 .
ANOVA results for cutting forces, deflection, sound pressure and milling errors Input parameters Fig. 16.Main effects plot-data means for cutting forces Fig. 17.Main effects plot-data means for tool deflection