Published: 31 December 2016

Application of evolution-based uncertainty design on gear

Boqiang Shi1
Yanhua Shen2
Guoqing Yu3
Guochen Duan4
Ruiyue Liu5
1, 2, 3, 4, 5School of Mechanical Engineering, University of Science and Technology Beijing, Beijing 100083, China
Corresponding Author:
Boqiang Shi
Views 33
Reads 14
Downloads 1447

Abstract

The evolution of mechanical parameters, a factor affecting the mechanical reliability, has gathered more attention nowadays. However, studies on time varying uncertainty can hardly be found. A new method based on evolution-based uncertainty design (EBUD) is applied to the design of gear in this paper. Considering the wear evolution over the lifetime, a tooth wear’s time-varying uncertainty model based on the continuous-time model and Ito lemma is established. Drift and volatility functions dependent on the drift rate and volatility rate of rotational speed and torque are used to express the time-varying uncertainty of tooth thickness. The method can predict the reliability and provide an instruction in reliability improving, maintenance and repair of the gear system.

1. Introduction

Gear transmission is the most important and widely used transmission form in mechanical systems. Almost all of the mechanical systems, from mechanical watch to nuclear power station, contain the gear transmission systems. The gear transmission system is mainly responsible for the transferring torque and power of the mechanical system. Once a failure occurs, it will lead to the collapse of the entire mechanical system. And there are various forms of gear failure. Process, materials and other factors may reduce reliability of gear. Therefore, it is particularly important to ensure the reliability of gear.

At present, there are a lot of literatures on the reliability analysis of gear. Ryazantsev A. A. [1] presented A method to prolong the life and improve the reliability by using the surface quenching of the open gear on the spherical ore-pulverizing mills. Starzhinsky, Victor E. [2] considered the employment of different statistical distribution parameters for gear reliability prediction, and described a method of predicting gearing reliability as a relation of the acting and permissible stress distributions. Netpu, Samroeng [3] analyzed the failure mechanism of gear from the aspect of material impurity, and improved the reliability of the gear from the aspect of material processing. Most of the existing literature focuses on reliability analysis, but there is little research on the method of reliability design of gears. Alemayehu, Fisseha M. [4] presented a novel probabilistic multibody dynamic analysis (PMBDA) that enhances the deterministic design practice of gears and gear systems, and implemented an advanced mean based on fast probability integration method to perform a reliability analysis. However, most of existing literatures focus on reliability analysis. there is little research on the method of reliability design of gears, and the influence of time factor on the reliability of gear is seldom considered. So far, the essence of gear design method is safety factor method. In order to ensure safety, the value of safety factor is always higher than the requirement. So, it can get an optimum gear. As the service time increasing, fatigue, wear, aging and other factors result in mechanical parameters changes, which should be paid more attention in mechanical design. It is necessary to use Evolution-based uncertainty design (EBUD), which is proposed in reference [5-7], in the key gear of mechanical system to predict and extend the life, predict and improve reliability of mechanical systems.

In this paper, the compare between the practical and the allowable value of tooth thickness is used as the failure criterion. Considering time effects on the system uncertainties, the integrated wear model is employed in the calculation of spur gear reliability, using the gear wear as the time varying uncertain parameter. As we can see from the work below the new method literally improves the reliability and the life of the gear. The method can also be used in the design of bevel gear, helical gear, and face gear.

2. Mathematical model of EBUD

For general system, the system performance index or variables used in the describing system status can be modeled as a stochastic process. The system uncertainty (or probability under some conditions, or reliability) at any time can be solved by the probability model which is the inequality relation about the value of real system performance and the value of the system required to achieve.

In order to model the general probability expression of evolution-based uncertain individual design method of the system, based on the references [5], the system status is expressed by the system individual performance output and individual allowable performance output function [6-9].

System evolution-based uncertain with individual data: the risky (or safety) existing in the system, in which the system performance should satisfy the regulated requirement (expressed by the inequality relationship of performance output and allowable performance output) under the specified environmental conditions at the regulated time. It can be described by the uncertainty (unreliability), or can be calculated by the certainty (or reliability). Considering the time-dependent uncertain characteristic of the system, the EBUD mentioned in this paper is to give the feasible design solution under the acceptable risk or reliability of the system.

The quantitative expression of system evolution-based uncertain is reliability, which means the probability of the system meeting the allowable performance output under the stated environmental conditional at the regulated moment. The math expression of the system meeting the performance output is the inequality relationship between the performance output Sx,t and allowable performance output Sy,t. It is general expression can be described as Eq. (1):

1
Sx,tSy,t.

If the system required that the performance output greater than or equal to the allowable performance output, those two output all multiply by –1:

2
S'x,t=-Sx,t,S'y,t=-Sy,t.

The normalized form is:

3
S'x,tS'y,t.

According to the above definition, the system reliability Rt over a time interval for the evolution-based uncertainty analysis can be written as Eq. (4) or (5):

4
Rt=PSx,tSy,t=PlnSx,tlnSy,t,
5
Rt=PS'x,tS'y,t=PlnS'x,tlnS'y,t.

According to the theory of EBUD, assumed the parameters x (or y) obeys Geometric Brownian Motion. λxi is drift rate of xit and δxi volatility rate:

6
dxit=λxixitdt+δxixitdwt.

Then, according to the Ito Lemma [10]:

7
dlnxit=λxi-δxi22dt+δxidwt.

Which means that the random variable xit conforms logarithmic normal distribution.

On the basis of the extension of the Ito Lemma which aims at multiple random process, lnSx,t or lnSy,t (use Gt to express) obeys Ito process:

8
dGt=i=1nGxiλixit+12j=1nk=1n2Gxjxkδjδkxjtxktdt
+i=1nGxiδixitdwit=μGtdt+i=1nσiGtdwit.

The mean μ^Gt and variance σ^G2t are:

9
μ^Gt=μ^G0+0tμGsds,σ^G2t=σ^G20+E0tσiGsdwis2.

If the system requires StSt, the system reliability must be:

10
Rt=Φμ^lnSt-μ^lnStσ^lnS2t+σ^lnS2t1/2.

If the requirement of system reliability is given, the original value of design variable must satisfy the Eq. (11):

11
fx0,y0=gZRt,t.

3. Tooth wear evolutionary model

As is shown in Fig. 1, gear 1 and gear 2 are engaged. gear 1 is driving gear, and gear 2 is driven gear. B1 is the point which the tooth enters the meshing process, and B2 is the point which the tooth exit. In a pair of teeth meshing process, meshing time:

tm0,θ0-θtω2that is tm0,tanαe2-tanαB2ω2.

3.1. Calculation of wear rate parameters

Using the integrated wear model, the wear rate is considered to be related to the contact stress p and the relative sliding speed v. The wear rate:

12
γ=Kpv.

K is wear coefficient, which is related to material and lubrication condition.

Relative sliding velocity of meshing point:

13
v=ρ1ω1-ρ2ω2,

where ρ1, ρ2 is meshing point’s radius of curvature. When the tooth profile is ideal involute, ρ1=K0B, ρ2=L0B:

14
v =K0Bω1-L0Bω2=K0L0-L0Bω1-L0Bω2
=RH1+RH2sinα-tanαkRO2ω1-tanαkRO2ω2
=RH1+RH2sinα-θ+αkRO2ω1-θ+αB2RO2ω2
=RH1+RH2sinα-tanαe2-ω2tmRO2ω1-tanαe2-ω2tmRO2ω1i.

Fig. 1Gear meshing contact stress at meshing point

Gear meshing contact stress at meshing point

Normal force of gear contact point Ftc:

15
Ftc=T2O2Bcosarctanθ0+αB2-ω1itm.

Meshing point contact stress (calculated in accordance with Hertz formula):

16
p=Ftc1ρ1+1ρ2π1-μ12E1+1-μ22E2b
=Ftc1RH1+RH2sinα-ω1itm+tanαB2RO2+1ω1it+tanαB2RO2π1-μ12E1+1-μ22E2b.

3.2. Calculation of time varying wear thickness calculation:

Wear thickness in a pair of teeth meshing process:

17
Δh=Kpvtt.

Tooth contact is considered as tow cylinder contact approximately. Width of contact deformation:

18
L=πpbFtc.

Contact time:

19
tt=Lsinarctanθ0+αB2-ω1itmO2Bω1i,

mesh thickness Δh’s Natural logarithm:

20
lnΔh=lnK+lnp+lnv+lntm.

In the actual situation, comparing with other parameters, the rotational speed and torque of the input vary largely with time’s changing. So, they can be considered as time-varying parameters. According to Eq. (7):

21
dlnΔh=lnΔhTμT+lnΔhvμv+12T+v2lnΔhσT2dt
+lnΔhTσTdwt1+lnΔhvσvdwt2
=12λT+λv-14δT2-12δv2dt+12δTdwt1+δvdwt2.

According to the Eq. (10):

22
lnΔhT~NlnΔh0+12λT+λv-14δT2-12δv2T,14δT2+δv2T.

Δht conform to logarithmic normal distribution, whose expectation is:

Δh0exp12λT+λvT.

And variance is:

exp14δT2+δv2T-1expλT+2λvT.

The Edgeworth series method is used to approximate the normal distribution of the logarithm normal distribution when calculating the total wear [11]. That is:

23
Fx=Φx-φx16θgiσgi3H2x+124ηgiσgi4-3H3x+172θgiσgi32H5x.

Φx – standard normal distribution function:

Φx=12π-xe-t22dt.

φx – Standard normal distribution probability density function:

φx=12πe-x22.

Hix is i order Hermite orthogonal polynomials:

H2x=x2-1, H3x=x3-3x, H5x=x5-10x3+15x.

σgi: standard deviation of log normal distribution.

θgi: third-order moments of lognormal distribution.

ηgi: fourth-order moments of lognormal distribution.

After the substitution, the original equation can be regarded as the normal distribution. The expectation of total wear thickness ΔhTsum is EΔhTsum, the variance is varΔhTsum. Time varying tooth backlash bc(T) obeys normal distribution whose expectation is bc0+EΔhTsum, and variance is varΔhTsum approximately.

4. EBUD of gear

The conditions of gear transmission are as follows. Transmission ratio is required ranging from 2.5-3, center distance ranging from 150-200 mm. The rotational speed n= 400 r/min when smooth running. The torque T= 110 N·m, this gear system works 8 h every day, 260 days a year. The failure criterion is that the tooth thickness of root circle is less than 90 % of initial tooth thickness. the material is steel and the lubrication condition is well, that is K 3×10-4. The wear reliability is required not less than 97.5 % after 8 years. Assumed that drift rate and volatility rate of rotational speed and torque is λT=λv= 2×10-11, δT=δv= 1×10-10.

Table 1The parameters of standard gear pairs

Small gear
Big gear
Modulus (m / mm)
3
3
Number of teeth (z)
35
95
Pressure angle (α / °)
20
20
Center distance (a / mm)
195
Pitch diameter (d / mm)
105
285
Addendum circle diameter (da / mm)
111
291
Root circle diameter (df / mm)
97.5
277.5
Base circle diameter (db / mm)
98.67
267.81
Tooth width (b / mm)
110
105
Tooth thickness of pitch circle (s / mm)
4.71
4.71
Tooth thickness of root circle (sf / mm)
5.91
7.07
Rotational speed when running smoothly (n / (r/min))
400
147.6
Elastic modulus (E / MPa)
200
200
Poisson ratio
0.3
0.3
Transmission ratio
2.71

The parameters of gear are determined after analyzing the gear’s failure mode and determining design criterions as is shown in Table 1.

According to the rotational speed and torque, a pair of teeth in the meshing frequency of the whole life cycle is N= 8×260×8×60×400 = 3.2×109.

(1) Determining the meshing time in a pair of teeth meshing process.

According to Fig. 1 and Table 1, tanαe2= 0.425, tanαB2= 0.308, so tm [0,7.6×10-3]

(2) Calculation of wear rate parameters.

According to Table 1 and Eqs. (13), (14), (16), (17), the wear thickness of small gear is shown in Fig. 2.

Fig. 2The function image of wear rate and time of one pair of teeth meshing

The function image of wear rate and time of one pair of teeth meshing

As is shown in Fig. 2, when T= 0, the wear thickness of root is Δh0=Kpvtt= 2.6513×10-11 mm.

(3) Calculation of time varying wear thickness calculation.

According to Eq. (21), (22), (23), and the time varying parameters of rotational speed and torque, Δh conform to logarithmic normal distribution, whose expectation is 0.0890, and variance is 0.0728. The allowable wear thickness Δh= 5.91×10 % = 0.591 mm, so the reliability:

R3.2×109=Φ0.591-0.08900.07281/2=Φ1.89=97.06 %.

The reliability cannot meet the requirements.

In order to satisfy the requirement of wear, positive correction should be used on designing the small gear. Modification coefficient x= 0.2. So, the modification coefficient of big gear is x= –0.2. The root circle diameter of small gear df'=df+2xm= 97.5+2×0.2×3 = 98.7 mm, tooth thickness of root circle change to 6.35 mm. After modification, the wear thickness of small gear is shown in Fig. 3. When T= 0, the wear thickness of root is Δhm(0)=Kpvtt= 1.9290×10-11 mm

Fig. 3The function image of wear rate and time of one pair of teeth meshing after modification

The function image of wear rate and time of one pair of teeth meshing after modification

The allowable wear thicknessΔh=6.35×10 % = 0.635 mm. Δh conforms to logarithmic normal distribution, whose expectation is 0.0648, and variance is 0.0728. The allowable wear thicknessΔh= 5.91×10 % = 0.591 mm, so the reliability:

R3.2×109=Φ0.635-0.06480.07281/2=Φ2.11=98.21 %.

The reliability can meet the requirements. Compared with original scheme, the tooth thickness changes from 5.91 mm to 6.35 mm, and the reliability improves from 97.06 % to 98.21 %.

5. Conclusions

The method of EBUD for gear systems is proposed in this paper considering the evolution and uncertain characteristics existing in the system. The drift function and the volatility function of the tooth thickness, the time varying parameters, are determined by the drift rate and the volatility rate of the rotational speed and torque. So, the tooth thickness is regarded as performance output, the allowable tooth thickness being the allowable performance output. They can reflect the uncertainty and evolution characteristics of the system. The gear system reliability model expressed in EBUD, inequality relationship of performance output and allowable performance output, is established on the basis of Ito Lemma and Ito Process. It can be calculated at any time by using the data of the system variables. By using EBUD, the reliability of gear increased by 1.15 %. This paper presents a new method for reliability design of gears, which has practical engineering significance.

References

  • Ryazantsev A. A. Analysis of means of reliability and service life growth for open gear drive of ore-pulverizing mills. Metallurgical and Mining Industry, Vol. 6, Issue 4, 2014, p. 6-22.
  • Starzhinsky Victor E., Soliterman Yuri L., Goman Arcadi M. Reliability prediction of gear transmissions. Proceedings of the ASME International Design Engineering Technical Conferences and Computers and Information in Engineering Conference, American Society of Mechanical Engineers, New York, 2008, p. 165-172.
  • Netpu S., Srichandr P. Failure of a helical gear in a power plant. Engineering Failure Analysis, Vol. 32, Issue 9, 2013, p. 81-90.
  • Alemayehu F. M., Ekwaro-Osire S. Uncertainty considerations in the dynamic loading and failure of spur gear pairs. Journal of Mechanical Design, Transactions of the ASME, Vol. 135, Issue 8, 2013, p. 084501.
  • Shi B. Q., Duan G. C., Shen Y. H., et al. Evolution-based uncertainty design for complex mechanical systems. Journal of Xi’an Jiaotong University, Vol. 49, Issue 3, 2015, p. 80-86.
  • Shi B. Q., Yan Y. Y., Fan H. F., et al. Mechanical design method with uncertain evolution. Journal of University of Science and Technology Beijing, Vol. 30, Issue 9, 2008, p. 1050-1054.
  • Yan Y. Y., Shi B. Q. Time dependent reliability analysis under uncertainty. Journal of Xi’an Jiao Tong University, Vol. 41, Issue 11, 2007, p. 1303-1306.
  • Li S. Lubrication and contact fatigue models for roller and gear contacts. The Ohio State University, 2009.
  • Miryam B. S., Miguel P., Jose I. P. Calculation of tooth bending strength and surface durability of internal spur gear drives. Mechanism and Machine Theory, Vol. 95, 2016, p. 102-113.
  • Ruey S. Tsay Analysis of Financial Time Series. Posts and Telecom Press, Beijing, 2010.
  • Cramer H. Mathematical Methods of Statistics. Princeton University Press, New Jersey, 1964.

About this article

Received
13 November 2016
Accepted
14 November 2016
Published
31 December 2016
Keywords
evolution-based uncertainty design
tooth wear
reliability