Published: 15 August 2016

Fuzzy control of active suspension system

Senthilkumar Palanisamy1
Sivakumar Karuppan2
1, 2Bannari amman Institute of Technology, Sathyamangalam, India
Corresponding Author:
Senthilkumar Palanisamy
Views 1423
Reads 804
Downloads 2225

Abstract

The main objective of this paper is to investigate the performance of active suspension system, using suspension deflection of the vehicle body as the principal criterion of control and fuzzy-logic as the control scheme. This work describes the application of fuzzy logic technique to the control of a continuously damping automotive suspension system. Active suspension systems are multivariable dynamic systems for which it is difficult to derive mathematical models. Therefore, analytical control schemes based on such models are complex to construct and generally do not perform well in practice. Hence intelligent control schemes like fuzzy logic controllers that can control the un modelled part of the suspension dynamics are simple to realize and can yield accurate control. This paper has described a proposed fuzzy control scheme for suspensions of the vehicle, because of its inherent ability to represent dynamics, the controller is easy to adapt for control tasks. The paper also describes the model and controller used in the study and discusses the vehicle response results obtained from a range of road input simulations. The simulation results obtained have confirmed the feasibility of the proposed fuzzy control scheme in Active suspension system.

1. Introduction

A suspension system plays a vital role in vehicle’s road handling and holding capacity by segregating the vehicle body from the road bumps and vibrations. Since the vehicle suspension system is important to the ride, comfort, and driving capability, design of a better quality suspension system for rough road surface condition is an important development objective for current automotive industry. An ideal vehicle suspension system should have the capability to reduce sprung mass displacement and acceleration and provide adequate suspension deflection to maintain tire-terrain contact. Since late 1970s, many types of suspension systems: passive [1, 2], semi-active [3] and active [4, 5] has been investigated and successfully implemented. Nowadays, more attention is being paid to the active system due to the fact that active suspensions have a potential to meet the performance requirements demanded by users. Various approaches have been discussed in order to design suitable control strategy for these active suspension systems. In recent years, the investigations of active suspension are being continued. Many researchers have been working on control strategies in order to improve the vibro-isolating properties of active suspension systems.

In all kinds of suspension systems, active suspension systems are more effective than others, such as passive or semi active suspension systems. Active suspension systems generally exhibit nonlinear and complex characteristics, so their mathematical models are difficult to accurately identify. Consequently, it is impractical to design model-based controllers for the control of active suspension systems. Fuzzy logic controller (FLC), based on fuzzy sets [6], are designed without system models for the development of the controllers and have been extensively employed to improve the control performances of active suspension system [7-9].

FLC can be designed based on some knowledge or without any knowledge about the control system. In addition, an appropriate fuzzy logic controller can overcome the environmental variation during operation processes. Therefore, it has been employed in the field of active suspension system. Fuzzy logic was first proposed by Lotfi A. Zadeh in 1965 and then he elaborated on his ideas in 1973 and introduced the concept of “linguistic variables”, Ro et al. [10] developed a fuzzy logic algorithm for an active ride comfort of a quarter-car model. Yester and Mcfall [11] and Cherry and Jones [12] employed fuzzy logic strategy for controlling an automotive suspension incorporating active elements. Huang and Chao [13-17] proposed a fuzzy control scheme to remove tire deformation from the control variable using a grey predictor for improving the control performance. However, the design of a traditional fuzzy controller depends fully on an expert or the experience of an operator to establish the fuzzy rules bank. There is no guide rule for designing the fuzzy rules bank and parameters [17-20]. Here FLC is designed with the objective to suppress the displacement and acceleration in the sprung mass so as to improve the service life of the suspension system and the ride quality of the car. The methodology is applied to a quarter-car suspension system. The remaining part of this paper is organized as follows. Section 2 contains a description of modeling for the suspension system. The control problem and the Controller designs is presented in Section 3. The resulting simulation are given in Section 4, and the conclusions in Section 5.

2. Modeling of suspension system

2.1. Mathematical modeling

Fig. 1 shows a quarter-car model of the suspension system. The sprung mass mb represents the vehicle body, and the unsprung mass mw is an assembly of the axle and wheel. The tire is assured to contact the surface of the road when the vehicle is traveling, and is modeled as a linear spring with stiffness kt. The linear damper, whose average damping coefficient is bs, and the linear spring, whose average stiffness coefficient is ks, consist of the passive component of the suspension system. The actuation force fs is acting between the sprung and unsprung masses. The state variables xb and xw are the vertical displacements of the sprung and unsprung masses, respectively, and r is the vertical road profile. Table 1 lists the parameters of the active suspension system.

Fig. 1Quarter car suspension model

Quarter car suspension model

Table 1Parameter values of active suspension system

Parameter
Value
Sprung mass (ms)
290 kg
Unsprung mass (mw)
59 kg
Damping coefficient of damper (Cs)
1000 N/m/s
Stiffness of damper (Ks)
16,812 N/m
Stiffness of tyre (Kt)
190,000 N/m
Actuation force (fs)
10000 N

2.2. System description

The dynamics for the suspension system, excluding the actuator and when the suspension travel is below its physical limit, is described by the linear Eq. (1) and (2):

1
mbx¨b+bsx˙b-x˙w+ksxb-xw=fs,
2
mwx¨w+bsx˙w-x˙b+ksxw-xb+ktxw-r=-fs,

where x¨b indicate the body acceleration; x¨w refers to the wheel acceleration; x˙w refers to wheel velocity; fs refers to actuator force. The motion equations of the quarter car model for active suspension can be written in state space form as follows:

X˙bX¨bX˙wX¨w=0100-KsMb-bsMbKsMbbsMb0001-KsMwbsMw-Kt-KsMw-bsMwXbX˙bXwX˙w+000fsMb00KtMw-fsMwru.

The output of the system in state space is represented as:

XbXb-XwX..w=100010-10-KsMwbsMw-Kt-KsMw-bsMwXbX˙bXwX˙w+0000KtMw-fsMwru.

3. Intelligent controller design

The whole premise behind intelligent control is that the system to be controlled does not have to be rigidly modelled. This is the biggest distinction between intelligent control and classical control. Here the designer only has to give the appropriate stimuli as input to the intelligent control and evaluate it based on its output. The intelligent control itself develops a model of the system to be controlled. Fuzzy logic, like most of the IC techniques attempts to model the way of reasoning that goes on in the human brain. It is based on the idea that the human reasoning is approximate, non-quantitative, and non-binary. In many cases, there is no black and white answer, but shades of grey.

3.1. Control problem

The control objective is to maximize the passenger comfort, while preserving the lifetime of suspension components, under road disturbances. The comfort is determined by the level of vertical car body acceleration experienced by the passenger. The lifetime of components is preserved by avoiding hitting of the rattle-space limits. Hence, the controller objectives can be stated as (a) increase, with respect to open-loop, the range of “typical” road disturbances for which the suspension travel limits are not reached, and (b) minimize the peaks of the body accelerations under road disturbances.

A p road input, Zr as described by Eqs. (3)-(5), is used to simulate the road to verify the developed control system. The road input described by as follow:

3
Zr1=-0.1,0t10,0,otherwise,
4
Zr2=0.11-cos2πt,1t2,0.41-cos2πt,2t4,0otherwise,
5
Zr3x=i=0NΔn2k10-3n0iΔncos2πiΔnx+φi,

where: x is the abscissa variable from 0 to L;L= 250 m; Δn= 1/L;nmax=1/B;N=nmax/Δn=L/B; k is a constant value depending from ISO road profile classification, it assumes integers increasing from 3 to 9, corresponding to the profiles from class A to class H; n0= 0.1 cycles/m; φi random phase angle following an uniform probabilistic distribution within the 0-2π range [21-22].

3.2. Fuzzy controller

The Fuzzy Logic Controller [10, 11] used in the active suspension has two inputs say body error (e), change in error (ce) of suspension travel and one output which has desired actuator force F. The control system itself consists of three stages: fuzzification, fuzzy inference machine and defuzzification. The fuzzification stage converts real-number (crisp) input values into fuzzy values, while the fuzzy inference machine processes the input data and computes the controller outputs based on rule base and the data base. These outputs, in fuzzy values, are converted into real-numbers by the defuzzification stage.

Fig. 2Layout of fuzzy logic control

Layout of fuzzy logic control

The schematic of fuzzy controller for active suspension is shown in Fig. 2. The process of converting a numerical variable into a linguistic variable (fuzzy number) is called Fuzzification. Under Fuzzy inference, the truth value for the premise of each rule is computed, and applied to the conclusion part of each rule. This results in one fuzzy subset to be assigned to each output variable for each rule. Mostly MIN or PRODUCT is used as inference rules. In MIN inference, the output membership function is clipped off at a height corresponding to the rule premise’s computed degree of truth (fuzzy logic AND). A possible choice of the membership functions for the mentioned variables of the active suspension system represented by a fuzzy set is as shown in Figs. 3 to 5.

Fig. 3Membership function for error

Membership function for error

Fig. 4Membership function for change in error

Membership function for change in error

Fig. 5Membership function for actuator force

Membership function for actuator force

For the rule basis, a classic interpretation of Mamdani was used. Under rule base, rules are constructed for outputs. The rules are in “If Then” format and formally the “If” side is called the conditions and the “Then” side is called the conclusion. A rule base controller is easy to understand and easy to maintain for a non- specialist end user and an equivalent controller could be implemented using conventional techniques. The rules table for fuzzy logic control is shown in Table 2.

The rule base used in the active suspension system can be represented by the following Table 2 with fuzzy terms derived by modelling the designer’s knowledge and experience.

Table 2Fuzzy rules table

C/Ce
NB
NM
ZE
PM
PB
NB
NB
NB
NM
NM
Z
NM
NB
NM
NM
ZE
PM
ZE
NM
NM
Z
PM
PM
PM
NM
ZR
PM
PM
PB
PB
ZR
PM
PM
PB
PB
The abbreviations used correspond to: NB: Negative Big; NM: Negative Medium;
ZE: Zero; PM: Positive Medium; PB: Positive Big; e: Error; ce: Change in error

Defuzzification is a process of converting fuzzy output to crisp number. There are more Defuzzification methods in which one of the most common technique is centroid methods. In the centroid method, the crisp value of output variable is computed by finding the variable value of the centre of gravity of membership function for the fuzzy value. This technique was developed by Sugeno in 1985. The only limitation of this method is that it is computationally difficult for complex membership functions [31]. The centroid defuzzification technique can be expressed as:

ZCOG=ZμAZZdzZμAZdz,

where ZCOG is the crisp output, μAz is the aggregated membership function and z is the output variable.

4. Simulation

The performance of the proposed fuzzy control scheme is illustrated in this section through a series of simulations. Simulation results are carried out using a quarter car model with active suspension, with two different road profile Zr1, Zr2 as shown in Figs. 6, 7 to demonstrate the efficiency of the proposed Fuzzy controller. For comparison purposes, the numerical results of the vehicle model with PID controller are also presented. PID control is perhaps the most widely used control method. It can provide fast response, well system stability and small steady state errors in a linear system with known parameters.

Fig. 6Road input signal Zr1 for simulation

Road input signal Zr1 for simulation

Fig. 7Road input signal Zr2 for simulation

Road input signal Zr2 for simulation

The result of the simulation of Fuzzy controller for road input Zr1 is shown Fig. 8. The four representative variables for controller evaluation are body displacement, suspension travel, Control force, body acceleration. From the Body Displacement, the settling time of passive suspension system is not stable and overshoot is very big. The output has an overshoot more than 20 % and settling time is long and not stable. Using the Fuzzy controller for suspension system, the results of overshoot is small and the settling time is also short. The suspension travel has an overshoot less than 20 % and a settling time shorter than 1 sec. The ride comfort is also improved by means of the reduction of the body acceleration with the help of fuzzy control scheme.

Fig. 8Response of suspension system for road input signal Zr1

Response of suspension system for road input signal Zr1

Fig. 9Response of suspension system for road input signal Zr2

Response of suspension system for road input signal Zr2

The results are shown Fig. 9 for the case with the road profile Zr2. Here, the overshoot and settling time are not acceptable for passive suspension. The system has the suspension travel with overshoot more than 50 % and a settling time longer than 3 sec. The fuzzy controlled system has less overshoot and settling time less than 1sec which indicates the efficiency of the proposed controller. The decrease in body acceleration magnitudes assures improved ride comfort as presented in body acceleration. There is not any permanent offset in suspension deflection which indicates that the proposed fuzzy control method is a suitable choice for implementation in active suspension.

The results are shown Fig. 10 for the case with the road profile Zr3. The fuzzy controlled system has less overshoot and settling time which indicates the efficiency of the proposed controller. It is seen that by using the proposed fuzzy controller the magnitudes for both vertical displacement and acceleration of the vehicle body are decreased significantly while passive suspension increased the magnitudes of both displacement and acceleration of the vehicle body. These results indicate that the ride comfort of the passengers is improved greatly by using the proposed FL controller.

Fig. 10Response of suspension system for road input signal Zr3

Response of suspension system for road input signal Zr3

5. Conclusion

Active suspension systems are multivariable dynamic systems for which it is difficult to derive mathematical models. Therefore, analytical control schemes based on such models are complex to construct and generally do not perform well in practice. On the other hand, intelligent control schemes like fuzzy logic controllers that can control the unmodelled part of the suspension dynamics are simple to realize and can yield accurate control. This paper has described a proposed fuzzy control scheme for suspensions of the vehicle, because of its inherent ability to represent dynamics, the controller is easy to adapt for control tasks. The simulation results obtained have confirmed the feasibility of the proposed fuzzy control scheme in Active suspension system, Further work should be considered if a robust adaptive fuzzy controller is to be designed for optimization of fuzzy rules.

References

  • Thompson A. G. Optimum damping in a randomly excited non-linear suspension. Proceedings of the Institution of Mechanical Engineers, 1969, p. 169-184.
  • Karnopp D. Analytical results for optimum actively damped suspensions under and excitation. ASME Journal of Vibration, Stress, and Reliability in Design, 1989, p. 278-283.
  • Crolla D. A. Semi-active suspension control for a full vehicle model. SAE Technical Paper Series, 1992, p. 45-51.
  • Goodall R. M., Kortm W. Active controlling round transportation – review of the state-of-the-art and future potential. Vehicle System Dynamics, Vol. 12, 1983, p. 225-257.
  • Hrovat D. Optimal active suspensions for 3d vehicle models. Proceedings of the American Control Conference, Arizona, USA, Vol. 2, 1991, p. 1534-1541.
  • Zadeh L. A. Fuzzy sets. Information and Control, Vol. 8, Issue 3, 1965, p. 338-353.
  • Kuo Y. P., Li T. S. S. GA-based fuzzy PI/PD controller for automotive active suspension system. IEEE Transactions on Industrial Electronics, Vol. 46, Issue 6, 1999, p. 1051-1056.
  • Lee S., Kim W. J. Active suspension control with direct-drive tubular linear brushless permanent-magnet motor. IEEE Transactions on Control Systems Technology, Vol. 18, Issue 4, 2010, p. 859-870.
  • Cao J., Li P., Liu H. An interval fuzzy controller for vehicle active suspension systems. IEEE Transactions on Intelligent Transportation Systems, Vol. 11, Issue 4, 2010, p. 885-895.
  • Ro P. L., Kim C., Kim H. Active suspension using fuzzy logic control. Proceedings of the American Control Conference, 1993, p. 2252-2253.
  • Yester J. L., Mcfall R. H. Fuzzy Logic controller for active suspension. SAE Papers, 1992, p. 259-270.
  • Cherry A. S., Jones R. P. Fuzzy logic control of automotive suspension systems. IEE Proceedings - Control Theory and Applications, Vol. 142, Issue 2, 1995, p. 149-160.
  • Huang S. J., Chao H. C. Fuzzy logic controller for a vehicle active suspension system. Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, Vol. 214, 2000, p. 1-12.
  • Hrovat D. Survey of advanced suspension developments and related optimal control applications. Automatica, Vol. 33, Issue 10, 1997, p. 1781-1817.
  • Williams R. A. Automotive active suspensions. Part 1: basic principles. Proceedings of the Institution of Mechanical Engineers, Vol. 211, Issue 6, 1997, p. 415-426.
  • D’AmatoF. J., Viassolo D. E. Fuzzy Control for Active Suspensions. Technical Report, Purdue University, Indiana, 1998.
  • Passino K. M., Yurkovich S. Fuzzy Control. Addison Wesley Longman, Inc., California, 1998.
  • Driankov D., Hellendoorn H., Reinfrank M. An Introduction to Fuzzy Control. Springer-Verlag, Berlin, Germany, 1993.
  • Rao M. V. C., Prahlad V. A tunable fuzzy logic controller for vehicle active suspension systems. Fuzzy Sets and Systems, Vol. 85, Issue 1, 1997, p. 11-21.
  • Yeh E., Tsao Y. A fuzzy preview control scheme of active suspension for rough road. International Journal of Vehicle Design, Vol. 15, Issue 1, 1994, p. 166-180.
  • Cebon D. Handbook of Vehicle Road Interaction. Swets and Zeitlinger, Lisse Netherlands, 1999.
  • Park S., Popov A. A., Cole D. J. Influence of soil deformation on off-road heavy vehicle suspension vibration. Journal of Terramechanics, Vol. 41, Issue 1, 2004, p. 41-68.

Cited by

Optimal FLC-Sugeno Controller based on PSO for an Active Damping System
Hoang Viet Nguyen | Feiqi Deng | Tien-Duy Nguyen
(2024)
Research on Electric Oil–Pneumatic Active Suspension Based on Fractional-Order PID Position Control
Yaozeng Hu | Jianze Liu | Zhuang Wang | Jingming Zhang | Jiang Liu
(2024)
Bộ điều khiển FLC-Sugeno tối ưu dựa trên PSO cho hệ thống giảm chấn tích cực
Nguyễn Hoàng Việt | Feiqi Deng | Nguyễn Tiến Duy | Nguyễn Duy Minh
(2023)
Predictive Suspension Algorithm for Land Vehicles over Deterministic Topography
Alejandro Bustos | Jesus Meneses | Higinio Rubio | Enrique Soriano-Heras
(2022)
Experimental and simulation investigation of vertical response of stepped torsion bar spring for light motor vehicle suspension system
Panneer Selvam Karuppiah | Pranesh Ganesan | Pannir Selvam Kasavan | Senthilkumar Sambasivam
(2022)
The AUN/SEED-Net Joint Regional Conference in Transportation, Energy, and Mechanical Manufacturing Engineering
Thi Thu Huong Tran | Tuan Anh Nguyen | Thang Binh Hoang | Duc Ngoc Nguyen | Ngoc Duyen Dang
(2022)
Active Suspension Control Using an MPC-LQR-LPV Controller with Attraction Sets and Quadratic Stability Conditions
Daniel Rodriguez-Guevara | Antonio Favela-Contreras | Francisco Beltran-Carbajal | David Sotelo | Carlos Sotelo
(2021)
Advances in Materials Research
K. R. Bharath Kumar | P. Senthil Kumar | K. S. Dharaneeshwarakumar | B. Deepak
(2021)
Terminal sliding mode control for full vehicle active suspension systems
Miaomiao Du | Dingxuan Zhao | Bin Yang | Lili Wang
(2018)

About this article

Received
06 December 2015
Accepted
22 April 2016
Published
15 August 2016
SUBJECTS
Vibration in transportation engineering
Keywords
fuzzy
PID
active suspension